Order # 114-8662664-9830652 — 13 items
BUNKER INDUST Trailer Brake Away Kit — 12V 5Ah battery, built-in charger, switch
Complete trailer breakaway system: weather-resistant case, internal 5Ah
battery, integrated charger, push-to-test LED, and the breakaway switch
with coiled cable. Side-mount installation.
Use: Session 02, complete
replacement for the brittle Cesco junction box and the old breakaway
battery.
Why this one: Buying as an integrated kit avoids piecemeal
failures; the new fresh battery resets the 3-5 year clock; built-in charger
ties cleanly into the aux 12V circuit from the truck.
View on Amazon (Amazon-exclusive brand) →
Ancor 124102 — Marine Grade Duplex Cable, 10 AWG, Red/Yellow, 25 ft
Tinned-copper marine-grade two-conductor cable. 10 AWG, flat profile,
red/yellow insulation for easy polarity ID.
Use: Session 01, runs
jack power from the disconnect output through the front wall and along the
tongue to the new Polestar.
Why this one: 10 AWG handles the jack's 30A peak draw with
margin; marine-grade tinning resists corrosion in outdoor wiring; the flat
duplex profile lies clean against the tongue.
View on Ancor →
NOCO NCP2 B603 — Battery Terminal Protectors, 50 pack
Oil-impregnated felt washers that slip over battery posts before clamping
the cable terminal. Anti-corrosion pads included in the same pack.
Use: Session 01 on the
new Renogy battery posts, plus a re-application step in
Session 04.
Why this one: Cheapest insurance against terminal corrosion;
50-pack is enough for years of trailer battery service plus the breakaway
battery; NOCO is the workshop standard.
View on NOCO →
Ancor 309225 — Marine Grade Heat Shrink Butt Connectors, 12-10 AWG, 25 pack
Adhesive-lined heat shrink butt connectors sized for 12-10 AWG wire.
Yellow insulation, marine grade.
Use: Session 01 (jack
power splicing, inline fuse holder), Session 02
(aux 12V tie-in), and Session 03 (any
larger gauge splices in the junction box).
Why this one: Yellow is the correct color code for 12-10
AWG; adhesive-lined means the heat shrink also seals against moisture once
you melt the adhesive with a heat gun.
View on Ancor →
Blue Sea Systems 2300 — 150A Common BusBar with 10 screws and cover
Insulated common bus bar with 10 #8-32 stud positions and a clear protective
cover. 150A continuous rating.
Use: Session 02, kept
from the original plan as expandable architecture for future 12V loads
(interior LED, USB outlet, accessory panel).
Why this one: One bus bar means future load additions don't
require disturbing the disconnect or battery terminals; Blue Sea is the
marine-industry standard for 12V distribution hardware.
View on Blue Sea Systems →
TICONN 200-Piece Heat Shrink Butt Connectors Kit — AWG 24-10, assorted
Color-coded heat shrink butt connector assortment in a storage case. Covers
24-22 AWG (red), 16-14 AWG (blue), 12-10 AWG (yellow) and finer sizes.
Use: Session 02 and
Session 03, smaller-gauge signal wire
splices (trailer light circuits, brake wire, ground).
Why this one: Trailer wiring uses several gauges; the
assortment means you have the right connector for every splice; 200 count
leaves plenty of spares for future work.
Find on Amazon →
TR Industrial Multi-Purpose UV Resistant Cable Ties — 8 inch, 100 pack
Black UV-stabilized nylon zip ties, 8 inch length, 100 count.
Use: All four sessions, securing wire runs along the tongue,
organizing splices inside the junction box, bundling loom-wrapped sections.
Why this one: UV-resistant nylon doesn't crumble after a
season in Colorado sun; 8 inch length handles typical bundling without
being so long they create flapping tails.
Find on Amazon →
Ancor 312225 — Marine Grade Heat Shrink Ring Terminals, 12-10 AWG, Size 8 Screw, 25 pack
Adhesive-lined heat shrink ring terminals sized for 12-10 AWG wire with
a #8 (small) stud opening.
Use: Session 02, bus bar
connections (the Blue Sea 2300 has #8-32 studs).
Why this one: #8 stud size matches the Blue Sea 2300 bus
bar exactly; ordering the #8 and 3/8" sizes separately (vs an assortment)
means you only buy what you need.
View on Ancor →
Alltooetools Battery Terminal and Post Cleaner Brush — SF0193
Two-ended wire brush tool: tapered male brush for cleaning cable clamp
interiors, female brush for cleaning battery posts.
Use: Session 01, clean
cable clamps and battery posts before final connection.
Why this one: Standard two-end design; works on any
automotive or AGM battery; keeps in the trailer toolkit for quarterly
maintenance.
Find on Amazon →
Alex Tech 25 ft Split Wire Loom Tubing — 1/2 inch, Black
Split (slit-down-the-side) corrugated wire loom in 1/2 inch diameter,
25 feet on a roll. Black UV-stabilized.
Use: Session 01 on the
jack power run, plus Session 04 on any
wire run still exposed after Session 02 and 03.
Why this one: Split design slips over already-installed
wires without disconnecting them; 1/2 inch handles the 10 AWG duplex and
smaller bundles; 25 ft covers the whole tongue plus the wheel-well runs.
Find on Amazon →
Blue Sea Systems 6005 m-Series — On/Off Battery Isolator Switch with Locking Key
Compact red rotary battery disconnect switch. 300A continuous, 3/8" studs,
removable locking key, mounting flange.
Use: Session 01, the
storage-mode disconnect that isolates loads from the battery when the
trailer is parked at the storage yard.
Why this one: Mandatory given off-site storage with no
shore power (parasitic drain math kills an AGM in 6 weeks otherwise); the
6005 m-Series is the industry-standard for trailer/RV applications; locking
key prevents accidental flips.
View on Blue Sea Systems →
Vrupin 188-Piece Rubber Grommets Kit — 10 sizes (1/4 to 1 inch)
Assorted rubber grommets in 10 sizes from 1/4 inch through 1 inch. 188 total
pieces in a storage box.
Use: Session 01, the
front-wall pass-through where the 10/2 duplex cable exits the V-nose.
Why this one: Variety means you find the right ID for any
hole you drill (1/2 inch hole takes a different grommet than a 5/8 inch
hole); leftover grommets become trailer toolkit stock for future
modifications.
Find on Amazon →
CURT 58272 — 7-Pin RV Blade Trailer Wiring Tester, Orange
Plug-in tester for 7-RV-blade trailer connectors. Individual LEDs for each
circuit; plug into the trailer-side cable end and the truck activates the
corresponding circuit.
Use: Session 03,
verifies each of the 7 circuits (ground, tail, left, right, brake, aux 12V,
reverse) after the cable replacement and color-matching.
Why this one: Eliminates the run-to-the-truck loop during
circuit testing; identifies wiring mistakes before you close the junction
box; orange housing is hard to lose at a comp lot.
View on CURT →
Order # 114-8986788-3791437 — 5 items, split shipment
POLESTAR Electric Trailer Jack — 5000 lb A-Frame, Hard Wiring, 9-27 inch Lift
Electric A-frame tongue jack with ball-screw drive, weatherproof cover, LED
work light, hard-wire connection (no plug-in cord), and manual crank
backup. 5000 lb dynamic / 7500 lb static rated.
Use: Session 01, mechanical
install plus power wiring from the Blue Sea disconnect.
Why this one: Ball-screw drive lasts longer than the
cheaper acme-thread designs; 7500 lb static rating handles the tongue
weight with margin; IP56 rating for Colorado weather; manual backup means
you're not stranded if the motor ever fails; hard-wire eliminates the
plug-in cord failure mode. Identified as 2026 OutdoorCarry "best overall"
in our research.
Find on Amazon →
Ancor 312625 — Marine Grade Heat Shrink Ring Terminals, 12-10 AWG, Size 3/8 Screw, 25 pack
Adhesive-lined heat shrink ring terminals sized for 12-10 AWG wire with
a 3/8" stud opening.
Use: Session 01, all
terminations at the Blue Sea 6005 disconnect (which has 3/8" studs) and
the battery cable ends.
Why this one: 3/8" stud size matches the Blue Sea 6005
m-Series disconnect; same Ancor adhesive heat-shrink construction as the
butt connectors (one heat-gun pass seals everything).
View on Ancor →
FEBRYTOLD 10 Gauge Inline Fuse Holder — Waterproof Pigtail with 30A and 40A Fuses
Pre-wired 10 AWG inline ATC blade fuse holder with weatherproof rubber boot
cover. Comes with 30A and 40A blade fuses.
Use: Session 01, installed
on the positive conductor of the jack power run within 18 inches of the
disconnect output stud.
Why this one: 10 AWG matches the Ancor 124102 duplex cable
exactly (no wire-size mismatch at the splice); waterproof boot for outdoor
mounting on the tongue; ATC blade fuses are the universal trailer fuse type.
Use the 30A fuse for the jack; keep the 40A as a spare or for a future
higher-current accessory.
Find on Amazon →
Renogy Deep Cycle AGM 12V 100Ah Battery
Maintenance-free sealed AGM deep cycle battery. 100Ah capacity, 1100A max
discharge, 3% self-discharge per month.
Use: Session 01, replaces
the wrong-chemistry Super Start starting battery currently in the box.
Why this one: AGM is the right cost/performance balance for
~8 events/year (lithium overkill given the calendar-age life limit at this
usage); 100Ah comfortably covers a comp weekend plus the parasitic loads
between events; Renogy is well-regarded in the solar/RV space at a sane
price point; maintenance-free means no electrolyte top-ups.
View on Renogy →
CRC Marine Premium Dielectric Grease — 3.3 oz
Non-curing silicone dielectric grease in a pressurized can with a precision
Select-A-Bead nozzle. Seals against moisture, prevents corrosion, safe on
plastics and rubber.
Use: All sessions, applied to every exposed terminal:
battery posts, disconnect switch studs, jack input lugs, fuse holder
contacts, junction box splices, 7-pin plug pins.
Why this one: Marine-grade formula is the right
environmental spec for trailer use; the Select-A-Bead nozzle lets you place
a precise dot without slathering; 3.3 oz is enough for the whole trailer
with leftover for the quarterly maintenance schedule.
View on CRC Industries →
Tools (crimper, heat gun, multimeter, drill, screwdrivers, wrenches) aren't in
these orders because they're either already in the workshop or planned as
separate purchases. The orders cover consumable parts and project-specific
hardware only.
Also picked up from hardware store (not in any Amazon order): 4 stainless #10 x
1.25" wood screws for mounting the Attwood box to the V-nose floor (~$3-5),
optional rubber anti-fatigue mat for vibration isolation under the box (~$10).
Items removed from the original cart during review and correctly excluded from
the final orders: